October 28, 2021

Professional Tool Reviews for Pros

Milwaukee Matrix Carbide Vs Shockwave 3.0 Driver Bits

Milwaukee Matrix Carbide Vs Shockwave 3.0 Driver Bits

Milwaukee Matrix Carbide bits hit the market hard with their carbide design and lifetime tip guarantee. But that doesn’t mean it’s the One Bit to Rule Them All. In fact, Milwaukee Shockwave driver bits are still incredibly relevant beyond their lower price. In this Milwaukee Matrix Carbide vs Shockwave 3.0 comparison, we’re going to look at the best times to use both.

Choosing Milwaukee Matrix Carbide and Shockwave 3.0 Driver Bits

  • Go with Milwaukee Matrix Carbide bits for highly repetitive jobs that usually wear down bits.
    • Drywall
    • Decking
    • Steel stud framing
    • Pre-fab
  • Milwaukee Shockwave 3.0 bits are best on for tasks that usually fracture bit tips.
    • Thicker metal fastening (14+ gauge)
    • Tapcons
    • Hard plastics

Milwaukee Matrix Carbide Vs Shockwave 3.0 Driver Bits

If you haven’t already, check out our article that goes into the details of Matrix Carbide driver bits and how Milwaukee designs them. Sorting our the Milwaukee Matrix Carbide vs Shockwave 3.0 debate boils down to the type of work you’re doing. Specifically, it’s about where your bits usually fail.

Milwaukee Matrix Carbide bits do their best work on highly repetitive tasks that cause your bit to fail because of tip wear. These are things like drywall, decking, steel stud framing, pre-fab, and more. They’re the kind of jobs that have you drilling more than 1000 screws a day into material that’s not terribly tough.

Matrix Carbid Vs Shockwave

Milwaukee Shockwave 3.0 bits are better in tougher driving applications like 14+ gauge metal fastening, Tapcon installation, and hard plastics. These jobs tend to fracture the tip rather than just wearing it down and you’re likely driving 100s of screws a day instead of 1000+.

Milwaukee Matrix Carbide Vs Shockwave 3.0 Driver Bits

That’s pretty much the extent of it. By choosing the right bit for the type of material you’re fastening, you get the best life and driving performance out of your bits.

Are you using Milwaukee Matrix Carbide or Shockwave 3.0 driver bits yet? Tell us what you think about them in the comments below!


Related articles

How to Ruin Your Power Tools and Make the Repair Man Happy

As one of the largest tool repair destinations in Central Ohio, Ohio Power Tool sees hundreds of tools in for repair each month. Unfortunately, much of the damage we repaired could have been avoided with just a few basic steps towards good tool maintenance. Sometimes, it seems, people ruin tools through lack of care and […]

Milwaukee Portable 6-Inch Tripod Chain Vise | 48-22-8690

Take Milwaukee’s Chain Vise Anywhere Chain vices see a lot of use in the field for electrical, plumbing, and mechanical contractors. But, according to Milwaukee, most of the vices we see on the market are difficult to transport, inefficient to deploy, and become unstable as the joints wear down from use. The Milwaukee Portable 6-Inch […]

DeWalt, Milwaukee, and Makita Drill Rough-in Challenge Video

We love testing drills on the PTR Test Track, but we’re ready to start pushing them a little harder. Today, we decided to run a rough-in challenge with drills from DeWalt, Makita, and Milwaukee Tool to see what they can do. Buy Here DEWALT DCD998 – https://amzn.to/3sij51u MILWAUKEE 2804 – https://bit.ly/3uNBvZK MAKITA XPH14 – https://amzn.to/3tngRzh […]

Notify of
Oldest Most Voted
Inline Feedbacks
View all comments
Anthony Barker

I think they really missed the boat by not making these for the purpose build drywall gun. that would have been a match made in heaven.

chuck martinez

Hey, weren’t these bits too brittle and prone to breaking?

Shaun Catlett

So how do they compare to the Wera Impaktor bits or the Wiha Terminator Impact bits?

Don Macleod

And get rid of the crappy Phillips screw & drivers- go with Robertson.

Mark Griffin

Carbide and a impact driver is just a bad combo period. Better wear your safety squints for real!!!! Carbide combined with heat and a impact, there’s no telling what will happen.

Would love your thoughts, please comment.x