September 21, 2021

Professional Tool Reviews for Pros

How to Safely Use a Table Saw

Using a table saw will allow a wide range of special cuts you couldn’t otherwise accomplish in your workshop or woodworking project. The main thing to remember when working with a table saw is this: Spinning blade + fingers = BAD. If your fingers ever get near the blade you have made an error in judgment or your technique is wrong. Like anything else, learning proper techniques can save you time – and in this case, fingers. A table saw is a very safe device to use if it is respected and you follow some basic guidelines.

Using a table saw will allow a wide range of special cuts you couldn’t otherwise accomplish in your workshop or woodworking project. The main thing to remember when working with a table saw is this: Spinning blade + fingers = BAD. If your fingers ever get near the blade you have made an error in judgment or your technique is wrong. Like anything else, learning proper techniques can save you time—and in this case, fingers. As part of our Training the Apprentice Series, we wanted to go over how to safely use a table saw, covering key safety tips and the devices or accessories that help make these tools safer.

How Do Accidents Happen?

According to surveys done by people who do this for a living, the number one cause for table saw accidents was familiarity and complacency with the tools. While fear is never good in the workshop, a healthy respect for your tools and the conscious adherence to basic safety procedures is a must. Surveys found that most accidents happened with veterans, NOT with novice users. While correlation doesn’t always equal causation, the survey did indicate that these veteran users were injured while doing something incorrectly—and not for the first time, either.

Continuing to use bad or risky techniques could eventually land you in the hospital. Knowing how to safely use a table saw means using good techniques. Let’s learn from their mistakes and be sure to follow proper safety procedures regardless of how long you’ve been using a table saw. Also, the presence of products like the Sawstop table saw system or the DeWalt DWE7499GD Table Saw with Guard Detect shouldn’t make you any more careless. It should be a last line of defense for a mistake. A safer user makes for a safer table saw.

Blade Proximity

There is never a reason to have your hands close to a spinning blade. Several different push devices exist on the market to help you, should you require assistance pushing a piece of wood through a spinning blade. In all honesty, you can buy a set of push sticks online or simply make one yourself. In either case, always use a push tool rather than your fingers for pushing a piece of wood past the blade. Note that devices with an actual handle will allow you to have greater control over the wood. Simple push sticks may not offer this and, as a result, are less helpful than their more robust counterparts.

There are lots of choices, but anything is better than your fingers when pushing wood past a blade

A push device keeps your hand farther away from the blade, placing itself between your hands and the spinning meat monster that would seek to devour your appendages. In all seriousness, I’d rather sacrifice a piece of wood or plastic to my hand any day. Things go wrong, you just don’t want to be near the blade when they do. Let’s face it—there is no such thing as a “minor” accident when you are dealing with a table saw. Your fingers are too important. Get some type of push stick…and use it.

How to Safely Use a Table Saw Guard & Splitter

All table saws come with a device that includes a riving knife (formerly a splitter) and a blade guard. The riving knife or splitter keeps the wood aligned with the blade after it passes through the cut. This prevents one of the more common reasons for a kickback. Kickback occurs when the wood catches on the back (lifting) part of the blade and comes flying back towards the user. It will ruin your whole day—we promise. Some wood is naturally stressed and so it tends to come back together after passing the blade.

The blade guard serves a few purposes. First and foremost it marks an area of “safety” around the blade which should not be violated. Secondly, helps prevent larger pieces of wood from falling or dropping onto a spinning blade. This event has nearly a 100% chance of resulting in a kickback.

Ask or observe many woodworkers, and you’ll find that they will admit to removing the blade guard from their table saws. Sometimes, it’s necessary to do this. For example—Pros remove the guard when cutting dados or using certain jigs. However, it’s important to replace this safety device when finished.

Don’t forget, because a blade guard and riving knife may be the only thing preventing a kicked-back piece of wood from launching itself straight at you. If it sounds like the table saw is a very scary tool—it’s not. It’s just that the occasional accident happens. You want to make sure you’ve followed proper procedures and guidelines so that when it does, you don’t get injured.

Using a Riving Knife

Modern table saws now include riving knives by default. These differ from splitters in that they raise and lower along with the saw. In fact, Underwriters Laboratories (UL) has required these in all table saws manufactured since 2009 in the United States in order to pass certification. This is good news for consumers. European users had these long before they became mandatory here in the States.

This protective device keeps wood from being able to close around or otherwise contact the backside of the blade. This prevents the most common reason for kickbacks. A riving knife differs from a traditional splitter in several ways:

  • It doesn’t need to be removed for cross cuts or blind cuts. These cuts don’t extend all the way through the wood. Because of this, it isn’t something you have to “remember” to put back
  • A riving knife is positioned much closer to the blade than a splitter. It provides even more kickback protection by keeping wood away from the back end of the blade.
  • The knife moves with the blade. It provides the same amount of protection regardless of the height of the blade

Anti-Kickback Pawls

Kickback pawls have spring-loaded spikes that dig into the wood if it happens to move backward against the blade. They work almost like an emergency fingerboard. On hardwood, they glide overtop during feeding and don’t tend to damage workpieces during normal operation. These are supplemental safety devices as your riving knife still serves as the first line of defense against kickbacks. They also don’t tend to work well on melamine.

As with all safety devices, you want to use these when possible and only remove them when you absolutely need to.

Blade Height

There are several schools of thought on setting table saw blade height. The thing is, there are two basic methods for setting blade height. A basic visual setting is sufficient when you plan on cutting through a piece of wood entirely. A precise setting is important when you want to make an exact depth of cut that doesn’t penetrate all the way through a piece of lumber.

For basic cuts, set the blade height correctly. Ensure the “gullets” (those curved troughs in between the blade teeth) sit at or just below the top of your wood. This affords the blade the best opportunity to cool itself during the cut. It also ensures the blades consistently make full contact. Exceptions to this rule are for when you are stopping the cut before you run the wood all the way through. In this scenario, you may want the blade all the way. This makes the angle of the wood at the end of the cut as steep as possible.

For precision depth cuts you’ll want to grab a 6″ combination square. This lets you set a measurement and then run the square over top of the blade until the highest part of the blade just contacts the square. After doing this run a test cut and use the square to test the depth of the cut. In this way, you will do much better than setting the blade depth by eye.

Speed of the Feed

The speed at which you send the wood through the blade will contribute to the ultimate quality of your cut. Go too fast and you risk chipping or splintering the end of your wood. This occurs because the blade doesn’t have enough time to naturally finish its cut. You can also task the blade too much and generate a kickback.

Go too slow and you can actually burn the wood. Using a sharp, quality blade helps make any cut better. Ultimately, you need need to develop a feel for the speed at which to feed wood through your saw. Keep in mind that different wood has different characteristics. Softer wood requires more speed than the same dimension of hardwood.

Let ‘er Rip

Ripping is done by placing the material against a fence and guiding it through the blade. You want to ensure it doesn’t twist or rock against the fence. This results in an extremely accurate cut, perfectly parallel to the opposite side. Rip cuts are easy. However, if you don’t use the provided blade guard or forget to replace the splitter, you take a greater risk of a kickback accident.

In general, you don’t want to cut pieces of wood smaller than 12-inches. This is because smaller pieces of wood are more difficult to control and can have unpredictable results. When you near the end of a rip cut, be sure to use a push tool to complete the cut. Never let your fingers get near the blade under any circumstances.

This most typically occurs when operators fail to use an “outfeed table” to catch long pieces of wood. This crucial add-on prevents you from having to apply a large amount of downward pressure to the remaining piece of wood still on the table in order to complete the cut. It also removes the temptation to put your hands near the blade to guide the wood all the way through. You want to spend your time working on the cut itself, not how to support the piece after it passes over the table. Using proper support after the cut can save you lots of hassle.

How to Safely Use a Table Saw for Crosscuts

You also need to know how to safely use a table saw for crosscuts. Miter gauges are never big enough for adequate cross-cutting in our opinion. As a result, we recommend adding a block of wood to the miter gauge (or building a sled). Add some 120 or 220 grit sandpaper to the edge. This trick gives you some extra traction as you make the cut.

Before making the cut, with the saw off, line up the piece with the blade. Ensure it will properly contact the blade at the exact measurement needed for the cut.

You want to make absolutely sure that the wood doesn’t move, shift, or rock against the miter gauge when you make your cut. Provided you keep everything secure, this can be one of the easiest cuts to make on a table saw. Avoid crosscutting long pieces of wood. Miter saws work best for this. Also, never use a miter gauge and a rip fence at the same time. This is a sure-fire recipe for a kickback and most manufacturers clearly warn against this in their user manuals.

One tip for making repetitive cuts is to clamp a short gauge block to the rip fence. This lets you line up the wood with the block, but the cut happens after the block. In this way, the piece never comes in contact with the rip fence/block AND the miter gauge at the same time. Since the block stops before the blade, the cut wood can fall easily onto the table. It keeps it from wedging between the fence and the blade following the cut.

Miter & Bevel Cuts

Miter cuts involve simply securing the wood at the appropriate angle using the miter gauge. Adding a gauge block/fence with a sandpaper cover will greatly aid in controlling the piece of wood and keeping it from slipping. When making a particularly steep miter cut, it greatly reduces the drag on the wood if you first make a 1/16th inch cut and then re-cut the wood along the same line.

When thinking through how to safely use a table saw for bevel cuts, you want to make good use of the rip fence and miter gauge. Use these to control the wood and ensure edges are straight against the fence and/or miter gauge. Waste can shoot off the table unexpectedly. It is also important to ensure that the waste side of the wood is never towards the fence. This means that the blade should always tilt away from the fence. This ensures the waste doesn’t get trapped against the fence and cause a kickback.

We also recommend positioning your body, when possible, behind the fence while performing a bevel cut. Continue to use your push tools to ensure that your hands never come in contact with the area around the blade.

When using a miter gauge to make bevel cuts, ensure the blade tilts away from the side you are controlling and that the waste end is falling under the shallow side of the blade. Never use a fence when using a miter gauge and making bevel cuts. When making bevel cuts you’ll find the blade behaves a little differently. This is due to the fact that it is cutting through more wood than it would through a vertical cut. Remember this as you feel your way through the cut and adjust speed accordingly.

Dados & Rabbets

We heartily recommend avoiding the wobble dado blades. These are special blades that curve around in order to provide a dado cut from a single blade. You can vary the angle to vary the width of the dado cut. The problem is that these blades don’t tend to make clean cuts in plywood, MDF, or veneer. Stacked dado blades provide a cleaner cut. Also, since you have multiple blades to make the cut, you also sharpen them less frequently. They work in a more predictable manner and are worth every penny provided you intend to use them on multiple projects.

Because the arbors on table saws vary, not every saw will be able to handle the full-width potential of every dado blade set. Remember, to be safe you need to have at least one full thread exposed over the nut after the blade is fully seated on the shaft. Benchtop and portable saws are the most likely to have reduced-size arbors, but we’re seeing this improve with contemporary models.

You also want to make sure your table saw throat plate supports a dado blade. Often, woodworkers have one plate for dadoes and another for single blades in order to capture more sawdust to the vacuum port.

How to Safely Use a Table Saw in Special Situations

If you are going to cut a dado or rabbet near the edge of a piece of wood, be sure to use a “sacrificial fence” that you clamp to the metal fence. This ensures the blade never contacts the metal fence and instead guides along your sacrificial fence during the cut. This trick also lets you cut narrower dados on the edge of a piece of wood without changing the stack. Making a sacrificial fence is as easy as clamping a piece of 1x material to your fence and allowing the dado blade to cut 1/4-inch or so into the fence up to its full height.

You can also add a featherboard to keep your wood tight to the table as you run it through the dado. If you use a featherboard, make sure your sacrificial fence is tall enough to allow the featherboard to be securely clamped. If you don’t want to make a featherboard, you can find several great kits here.

Keep the speed steady when making rabbet cuts. You want the blade to do the work, and do it evenly. Forcing the wood through can tear your edges and result in an uneven depth of cut. You also want to test the cut on a scrap piece of wood and measure (or test fit) it to be sure you are getting the exact depth and width you need.

The Final Word

The best thing you can do when learning how to safely use a table saw is to take your time and think about what you are doing. If you sense you are doing something dangerous, you probably are. You should never have the board come in contact with both the ripping fence and the miter gauge at any time. Also, never put your fingers anywhere near the blade—always use a push device. A table saw gives you many years of service and allows accurate cuts to be made. Many other tools cannot make the same claim. Once you get the hang of it and treat the tool with the respect it deserves, you’ll be more than happy you bought it.

Related articles

Huskie Tools Series 7R Pro Line Tools Run On Milwaukee Batteries

Huskie Tools Expands 7th-Gen Hydraulic Tool Line Onto M18 Battery Platform Huskie Tools makes equipment designed for Pros working in the utility trades. The Huskie Series 7R Pro Line includes 61 new battery-powered hydraulic tools. While that seems newsworthy, they also made the new lineup work with one of the most widely available battery platforms: […]

No You Should NOT Buy an Extended Warranty – 8 Reasons Why

I have gone over a decade without buying an extended warranty. Along the way, I learned a thing or two about the practice which seems to dominate the time and energies of associates and salespeople at many retail locations. The extended warranty market is big business. In fact, companies often outsource extended warranties to larger […]

Notify of
Oldest Most Voted
Inline Feedbacks
View all comments
David Sherwood

About a year ago, I got a great deal on the big folding roll-around DeWalt 10″ contractors table saw that normally sells for $500.. on sale & with store credits for only $340. I didn’t need it.. but it was just to good to pass up. Its been sitting in the garage ever since. It has the flip-up fence… and with the roller supports can handle a full sheet of plywood.

Would love your thoughts, please comment.x