Makita XDT16 Cordless Drill Reviews & Impact Drivers

18V/20V Max Impact Drivers

Speed Under Load
Measured Torque
Weight
Feature Set
Value
Final Thoughts

The Makita XDT16 Brushless Impact Driver presents a really potent mix of speed and torque, and it does it in an incredibly compact, and lightweight package. With its automatic smart modes, it has a feature set that should help keep both your bits and fasteners intact. If you need an impact driver that just about ticks off all conceivable boxes, this is the tool for you.

Overall Score 4.4 Shootout Results

Buy it Online

Shop Now

Makita XDT16 18V LXT Brushless Impact Driver Review


The Makita XDT16 Puts Together a Complete Package to Take the Crown

We tested 30 impact drivers in a head-to-head contest to see which model has the best speed, power, ergonomics, and value. While the competition was intense, the Makita XDT16 Brushless Impact Driver edged out the competition to take an overall 1st place finish.

Makita XDT16 Shootout Results

  • 18V Ranking: 1st place out of 16
  • Speed Under Load: 651 RPM (1st place)
  • Fastening Torque: 2131 in-lbs (8th place)
  • Nut-Busting Torque: 3300 in-lbs (tie, 4th place)
  • Decibels Under Load: 97 dB(A) (tie1st place)
  • Weight: 2.0 pounds bare, 2.9 pounds with compact battery (2nd place)
  • Footprint: 4.6″ head length, 7.4″ height (1st place)
  • Feature Set: Highlighted by 4 auto smart modes, programmable mode switch (1st place)
  • Value: $177.99 bare, $281.29 kitted with two 5.0Ah batteries (8th place) 

*Based on test results as of February 11, 2019. Check our Best 18V Impact Driver page for the latest updates.

Takeaway

The Makita XDT16 Brushless Impact Driver presents a really potent mix of speed and torque, and it does it in an incredibly compact, and lightweight package. With its automatic smart modes, it has a feature set that should help keep both your bits and fasteners intact. If you need an impact driver that just about ticks off all conceivable boxes, this is the tool for you.

SUPPORT OUR ADVERTISERS

Performance

We tested each impact driver’s speed and torque. To learn more about the details of our testing methods, head over to our Best Impact Driver main page.

Makita claims that the XDT16 delivers 3,600 max RPM (no-load speed) and 1,600 in-lbs of torque. The good news is that torque value undersells what this impact driver is actually capable of.

Speed Under Load

The XDT16 fired off a really brisk 651 RPM under load. This speed is significantly faster than the 2nd place Metabo HPT WH18DBDL2’s 573 RPM. The fact that only half of the impact wrenches we tested could maintain a 500+ RPM makes this tool’s substantial lead all that much more impressive.

Makita XDT16

Fastening Torque

On the one hand, this category presents us with the Makita XPT16’s worst performance – 2131 in-lbs of fastening torque for an 8th place finish. While an 8th place finish isn’t necessarily awe-inspiring, this figure does far exceed the 1500 in-lbs we want to see for a Pro-grade impact driver.

Nut-Busting Torque

Interestingly enough, while the Makita XDT16 is merely adequate at tightening down bolts, it winds up being way more impressive at taking them off. With 3,300 in-lbs of nut-busting torque, this impact driver finishes in a strong 4th place (tied with Ridgid’s R86037N). Only Milwaukee’s Gen 3 M18 Fuel, Kobalt’s 24V, and Skil’s 20V pull more breakaway torque than Makita in our tests.

Weight and Footprint

As a bare tool, Makita’s impact driver comes in at just under 2 lbs. With a 2.0Ah battery attached, it still manages to punch in at 2.9 lbs. Only the Mac Tools MCF886 model is lighter.

Makita XDT16

However, no other 18V impact driver currently matches the XDT16’s size. With an overall length of 4.6″ and an overall height of 7.4″, it’s just a touch smaller than Milwaukee’s 2857.

Makita XDT16

Overall, the Makita XDT16 finishes in 1st and 2nd place for size and weight, respectively. Fitting into tight spots and keeping your fatigue level down is a simple affair with this impact driver.

Decibels

There’s no getting around it, impact drivers are really noisy tools. So, when we refer to a “quiet” impact wrench, we mean it in a relative sense. The Makita XDT16 is one of the quietest impact drivers we tested.

It sounds off at an almost church-mousey 97 dB(A), which puts it in a two-way tie with the Hilti SID 4-A22 for a first-place finish in the noise category. While it might be the quietest, you’ll still want hearing protection if you plan to use it for any extended amount of time.

Feature Set

The Makita XDT16 earns the top ranking for its feature set, based in large part on its 4 auto smart modes and programmable mode switch.

The Assist mode helps eliminate screw cam out and cross threading by driving at low speed until the actual tightening begins. Once it senses the screw dig in, it ramps up to full speed.

Two tightening modes help with faster starting with self-drilling screws in thick or thin gauge metals before backing off at the end so you don’t shear off the head.

Finally, a reverse rotation auto-stop mode puts a halt to rotation and impacts when the fastener has loosened up. This is very convenient when you’re working on an engine or on bolts overhead and want to hand thread them off.

Cycle between the four assist modes with the “A” button.

Makita XDT16

There’s also a Quick Mode Shift button above the trigger. You can use it either cycle through the four standard speed modes or program in your favorite.

To program the button, put the impact driver in the mode you want to save. Press and hold the Quick Mode Shift button and mode change button (hammer and drill icon) and hold it until you see the “C” LED blink green. Now the button will cycle back to that mode from any other.

To clear it and go back to standard mode cycling, press and hold the light button and programmable button until the panel flashes.

You can turn the Quick Mode Shift button on or off by pressing and holding it and the Assist (“A”) button.

Quick Mode Shift is helpful if you want to work between just one speed mode and an assist mode or a couple of speeds and switch with one hand. You can set it however you like, so you can work with a combination of any two modes you want.

Other Features

  • Brushless motor
  • Dual LED lights on the chuck
  • Belt hook

Makita XDT16

Value

This tool hasn’t hit the shelves quite yet and doesn’t have a firm retail price. Because it’s replacing Makita’s previous top-of-the-line impact wrench, the XDT12, we’re expecting the XDT16 to have a similar pricing structure – around $281.29 as a kit with two 5.0Ah batteries and a charger, or around $177.99 for the bare tool.

This price point puts the XDT16 in 8th place for value. The presence of Prosumer models skews that somewhat and Makita scores a more respectable 80 points when you only consider the Pro brands.

SUPPORT OUR ADVERTISERS

The Bottom Line

The Makita XDT16 Brushless Impact Driver presents a really potent mix of speed and torque, and it does it in an incredibly compact, and lightweight package. With its automatic smart modes, it has a feature set that should help keep both your bits and fasteners intact. If you need an impact driver that just about ticks off all conceivable boxes, this is the tool for you.

Makita XDT16 18V LXT Brushless Impact Driver Specifications

  • Model: XDT16Makita XDT16
  • Power source: 18V LXT Lithium-Ion Batteries
  • No Load Speed (for each mode): 0-1100 / 0-2100 / 0-3200 / 0-3600 RPM
  • Maximum Torque: 1600 in-lbs
  • Impact Rate: 0-1100 / 0-2600 / 0-3600 / 0-3800 IPM
  • Bare Weight: 1.9 lbs
  • Weight with Battery: 2.9 lbs
  • Length: 4.6 in
  • Height: 7.4 in
  • Warranty: 3-Year Limited Warranty
  • Price: $281.29 for the kit, $177.99 bare

6
Leave a Reply

avatar
5 Comment threads
1 Thread replies
0 Followers
 
Most reacted comment
Hottest comment thread
6 Comment authors
Ed DrezninSizarro BarkieJason GallupChris LambingRay Chee Recent comment authors
  Subscribe  
newest oldest most voted
Notify of
Sizarro Barkie
Guest
Sizarro Barkie

Nice hardware.

Jason Gallup
Guest

Let’s be real here . All these drills are great for different reasons. We as trades people, DIY’ers , homeowners are blessed with the variety of different ranges of durability and price ranges available today. I remember helping my grandfather build docks and do home repairs using a huge cast aluminum corded drill made by Thor. It had no speed setting or torque settings. Had a Jacob’s keyed chuck on it that had to be lubricated constantly. Guaranteed to strip a few screws and sometimes snap the screw heads . But it was always better than using a brace hand… Read more »

Chris Lambing
Guest

Makita is the only way to go!

Ray Chee
Guest

#MakitaTrailblazers
I Love Makita!

Joshua Mckinney
Guest

Doesn’t surprise me that this just got ranked the #1 overall impact in the latest showdown. I own the xdt14 and it’s a wonderful tool. If you go the makita route you won’t be disappointed