fbpx
October 28, 2021

Professional Tool Reviews for Pros


Milwaukee Switchblade Self-Feed Bits – Legal Everywhere

Best Lightweight Drill for a Woman - Milwaukee

Milwaukee SwitchBlade Self-Feed Bits Let You Switch Instead of Sharpen

We worked with Milwaukee on accessories for our epic best cordless drill head-to-head to cover light and heavy load testing. On the light side, their Red Helix Titanium Twist Bits gave us a benchmark for high-speed work. To put our drills under a heavier load, we turned to Milwaukee self-feed bits, particularly their SwitchBlade bits that give you the ability to change the blade instead of the entire bit.


Milwaukee Self-Feed Bits Design

Replaceable Blades

The dominant feature on these Milwaukee self-feed bits is the replaceable blade. Self-feed bits aren’t cheap, and many Pros sharpen them several times before tossing them. Milwaukee SwitchBlade bits let you do away with sharpening and just swap out the blade.

Milwaukee Self-Feed Bits: A Switchblade That's Legal Everywhere

Making the switch is pretty simple. Grab a 3mm hex wrench to remove the set screw on the shaft. That releases the threaded feed bit that slips straight out. Once it’s out of the way, you can pull the blade out and change it for a new one. Slide your feed screw back in, tighten the set screw down and you’re ready to go. In practice, it takes about 45 seconds without rushing.

Replaceable Feed Screw

Feed screws don’t need to be replaced as often as the cutting blades, but the design allows for that, too. It’s another easy swap since removing it is already part of the blade replacement process.

Additional Features

  • 7/16″ hex shank
  • Inside cutting plane smooths out holes
  • 1-3/8″ to 2-9/16″ diameters available.

Performance

We set up a pretty aggressive test series using OSB subflooring to give us consistent material. Between it and gluing up the layers, it’s a much tougher material to drill through than untreated SPF or other softwoods.


Milwaukee Self-Feed Bits: A Switchblade That's Legal Everywhere

With that material choice, nearly every drill we tested had to work at low speed with a 2-9/16″ Milwaukee self-feed bit. The exception is Hilti’s 4-speed monster that was able to make it through in its 2nd gear.

But many Pros that use this type of bit are working rough-ins in softwoods and there are plenty of drills, like the Milwaukee Gen 3 M18 Fuel, that have the ability to make that hole at high speed. Between the horsepower of its brushless motor and a bit that’s sharp more often because of its simple replacement, you’re getting through that stage of your work faster and without having to turn to a Super Hawg.

One of the major benefits of using a self-feed bit is its self-feeding tip. The threads Milwaukee uses hold well as it pulls the bit through. The cutter designs shave out the sides, leaving a cleaner hole and reducing bit bind up significantly.

Milwaukee Self-Feed Bits: A Switchblade That's Legal Everywhere

In drilling hundreds of holes in our shootout, the only stops we experienced were when the motor shut down because the load was too great—not because the bit bound up. We were drilling straight down, and the bind-up risk goes up if you’re attacking at an angle. However, this bit is going to bind up less often than spade bits or hole saws.

Price

Milwaukee SwitchBlade self-feed bits come in 6 common diameters and a set. They’re more expensive than other self-feed bits on the market, but their usable life is much longer and you don’t have the downtime and cost of sharpening them. Over their life, you’ll save money over standard self-feed bits.

Replacement blades vary depending on the size. There are singles, 3-packs, and 10-packs (includes 2 feed bits, set screws, and a hex wrench). There’s also a feed bit (2)/set screw (2)/hex wrench set available.

The Bottom Line

Milwaukee SwitchBlade Self-Feed Bits drill efficiently, give you a longer useable life than other self-feed bits, leave a cleaner hole, bind up less often, and save you time and money over the long haul. They’re the perfect fit for Pros that do a lot of repeat drilling for rough-ins or installs.

Related articles

How to Ruin Your Power Tools and Make the Repair Man Happy

As one of the largest tool repair destinations in Central Ohio, Ohio Power Tool sees hundreds of tools in for repair each month. Unfortunately, much of the damage we repaired could have been avoided with just a few basic steps towards good tool maintenance. Sometimes, it seems, people ruin tools through lack of care and […]

Milwaukee Portable 6-Inch Tripod Chain Vise | 48-22-8690

Take Milwaukee’s Chain Vise Anywhere Chain vices see a lot of use in the field for electrical, plumbing, and mechanical contractors. But, according to Milwaukee, most of the vices we see on the market are difficult to transport, inefficient to deploy, and become unstable as the joints wear down from use. The Milwaukee Portable 6-Inch […]

DeWalt, Milwaukee, and Makita Drill Rough-in Challenge Video

We love testing drills on the PTR Test Track, but we’re ready to start pushing them a little harder. Today, we decided to run a rough-in challenge with drills from DeWalt, Makita, and Milwaukee Tool to see what they can do. Buy Here DEWALT DCD998 – https://amzn.to/3sij51u MILWAUKEE 2804 – https://bit.ly/3uNBvZK MAKITA XPH14 – https://amzn.to/3tngRzh […]

Subscribe
Notify of
guest
1 Comment
Newest
Oldest Most Voted
Inline Feedbacks
View all comments
Michael T

Can the replaceable blades be sharpened? I could imagine sharpening a few in one session being much more efficient than sharpening a fixed blade bit and the cost savings would then be tremendous.

1
0
Would love your thoughts, please comment.x
()
x